View STK4040XI_191991.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Ordering number : EN4621A
Thick Film Hybrid IC
STK4040XI
AF Power Amplifier (Split Power Supply) (70 W min, THD = 0.008%)
Features
* Compact packaging supports slimmer set designs * Series designed from 50 up to 150 W and pincompatibility * Simpler heat sink design facilitates thermal design of slim stereo sets * Current mirror circuit, cascade circuit and purecomplimentary circuit application reduce distortion to 0.008 % * Supports addition of electronic circuits for thermal shutdown and load-short protection circuit as well as pop noise muting which occurs when the power supply switch is turned on and off.
Package Dimensions
unit: mm 4075
[STK4040XI]
Specifications
Maximum Ratings at Ta = 25C
Parameter Maximum supply voltage Thermal resistance Junction temperature Operating substrate temperature Storage temperature Available time for load shorted Symbol VCC max j-c Tj Tc Tstg ts *1 VCC = 43.5 V, RL = 8 , f = 50 Hz, PO = 70 W Condition Rating 63 1.4 150 125 -30 to +125 1 Unit V C/W C C C s
Recommended Operational Conditions at Ta = 25C
Parameter Recommended supply voltage Load resistance Symbol VCC RL Condition Rating 43.5 8 Unit V
SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN
N3096HA (OT)/O2093YO 5-2189 No. 4621-1/5
STK4040XI Operating Characteristics at Ta = 25C, VCC = 43.5 V, RL = 8 , VG = 40 dB, Rg = 600 , 100 k LPF ON, RL (non-inductive)
Rating Parameter Quiescent current Output power Total harmonic distortion Frequency response Input resistance Output noise voltage Neutral voltage Symbol ICCO PO THD fL, fH ri VNO*2 VN Condition VCC = 52.5 V THD = 0.008 %, f = 20 Hz to 20 kHz PO = 1.0 W, f = 1 kHz +0 PO = 1.0 W, dB -3 PO = 1.0 W, f = 1 kHz VCC = 52.5 V, Rg = 10 k VCC = 52.5 V -70 0 20 to 50k 55 1.2 + 70 min 15 70 0.008 typ max 120 Unit mA W % Hz k mVrms mV
Note: Use rated power supply for test unless otherwise specified. *1 When measuring permissible load short time and output noise voltage use transformer power supply indicated below. *2 Output noise voltage represents the peak value on the rms scale (VTVM). The noise voltage waveform does not include the pulse noise.
Specified Transformer Power Supply (MG-200 Equivalent)
Equivalent Circuit
No. 4621-2/5
STK4040XI
Application Circuit: 70W min Single Channel AF Power Amplifier
Sample Printed Circuit Pattern for Application Circuit (Copper-foiled side)
No. 4621-3/5
STK4040XI
Description of External Parts
R1, C1 C2 : Input filter circuit * Reduces high-frequency noise. : Input coupling capacitor * DC current suppression. A reduction in reactance is effective because of increases in capacitor reactance at low frequencies and 1/f noise dependence on signal source resistance which result in output noise worsening. : Input bias resistor * Biases the input pin to zero. * Effects VN stability (refer to NF circuit). * Due to differential input, input resistance is more or less determined by this resistance value. : NFB circuit (AC NF circuit). Use of resistor with 1% error is suggested.
R2
R4, R5 C3 (R2)
R3 R6, R7 R7, C4 C6, C9 C8 C5 R8, C10 R9, C13 C11, C12
: : : : : : : : :
R10
:
* VG settings are obtained using R4 and R5 according to the following equation: R log20* 5 40 dB is recommended. R4 * Low-frequency cutoff frequency settings are obtained using R 4 and C3 according to the following equation: 1 fL = [Hz] 2*R4*C3 When changing the VG setting, you should change R4 which requires a recheck of the low cutoff frequency setting. When the VG setting is changed using R5, the setting should ensure R2 equals R5 so that VN balance stability is maintained. If the resistor value is increased more than the existing value, VN balance may be disturbed and result in deterioration of VN temperature characteristics. Differential constant-current bias resistor For oscillation suppression and phase compensation applications (For use with differential stage applications) For oscillation suppression and phase compensation applications (A Mylar capacitor is recommended for C4 for use with output stage applications) For oscillation suppression and phase compensation applications Power stage (Must be connected near the pin) C6: Positive (+) power C9: Negative (-) power For oscillation suppression and phase compensation applications (Oscillation suppression before power step clip) For oscillation suppression and distortion improvement applications Ripple filter circuit on positive (+) side. Ripple filter circuit on negative (-) side. For oscillation suppression applications * Used for reducing power supply impedance to stable IC operation and should be connected near the IC pin. We recommend that you use an electrolytic capacitor. Output resistor Increases load shorting endurance capacity during times of high output.
No. 4621-4/5
STK4040XI
s No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. s Anyone purchasing any products described or contained herein for an above-mentioned use shall: Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. s Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of November, 1996. Specifications and information herein are subject to change without notice. No. 4621-5/5

▲Up To Search▲

Price & Availability of STK4040XI

	To Download STK4040XI Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .